Installation Guide

Madimack heat pumps

Use the shared Madimack heat-pump integration to select heating, cooling or automatic operation and verify the response.

← All equipment guides
ConnectionSupported RS-485 interface
Choose in ClyrHeat Pump → Madimack Inver-series
When you finishMode, setpoint and equipment response checked

01 / Start with the right guide

Match your equipment

Clyr’s tested Madimack heat-pump integration uses the Inver-series selection. Identify the exact model and control-board revision; heating-only and reversible units do not necessarily offer the same operating modes.

  1. 1Clyr app
  2. 2Clyr RS-485 interface
  3. 3Madimack heat-pump controller

How the parts work together. This is a system overview, not a terminal wiring diagram.

02 / Get ready

Before you start

  • Record the equipment model, controller generation and installed software version. Use the matching product manuals.
  • Have a qualified installer isolate every relevant electrical supply and verify absence of voltage before opening equipment. Turning it off in the app does not isolate power.
  • Confirm the circulation pump runs and water is flowing before requesting heat, cooling or chlorination. Keep the manufacturer’s interlocks and flow protection in place.
  • Have bypass position, water-flow requirements, temperature sensing and equipment clearances checked by the installer.

03 / One step at a time

Set it up

  1. Record the installation settings

    Record the approved RS-485 connection, network and Modbus address. Clyr’s heat-pump form accepts addresses 1–16; the selected address must match the unit. Keep the manufacturer’s protection and shutdown requirements intact.

  2. Add the heat pump

    Open Settings → Devices → Add, then select the Clyr controller physically connected to this equipment. Open Pool Equipment and choose the item named below. App wording can vary by version.

    Choose Heat Pump, then Madimack Inver-series. Give it a clear name, select the physical network and enter the matching Modbus address. Choose the commissioned temperature setpoint.

  3. Choose a mode the unit supports

    Use Heat for warming, Cool only on a cooling-capable unit, and Auto only where supported and commissioned. A selected mode is a request; temperature demand, flow, delays or a fault can keep the compressor idle.

  4. Observe a complete operating response

    With circulation established, select the commissioned mode and setpoint. Compare local mode, inlet/outlet temperature and fault indications with Clyr. Allow manufacturer-required delays; do not rapidly cycle power to force a start.

  5. Make the schedule match the installation

    After the manual checks pass, create the required event in Clyr. Review its start, finish and equipment settings. Keep heating and chlorination within verified pump operation; an overlapping schedule is not a safety interlock.

    Shared app skill · not equipment wiring

    Follow the Clyr scheduling workflow. Select the equipment in this guide and use the times and settings commissioned for your pool.

    Open on YouTube · 0:00–1:51 ↗

04 / Prove the result

Check it works

A saved setting tells you what you requested. These checks tell you what the equipment actually did.

  • Clyr and the local display agree on the intended operating mode.
  • Temperature readings are plausible and the unit responds when there is demand.
  • Any defrost or protective delay is understood, rather than treated as a communication failure.
  • OFF and the planned circulation/cooldown sequence are checked.

05 / Find the next useful check

If something is wrong

The device is saved, but it does not respond

Check the selected controller, equipment type, physical network and address against the installer’s record. Check the equipment’s own display for a fault. Isolate power before inspecting connections.

Manual control works, but the schedule does not

Check the event’s day, time, selected device and requested value. Check whether Manual or Service mode is overriding scheduled operation. Return to the intended mode and observe the next event.

06 / Save for later

Keep these handy

Choose the right Clyr networkSchedules, programs and Autopilot

Product instructions

Use the manual supplied with your exact equipment and controller revision. If the connectors, labels or app choices differ, stop and contact Clyr with a photo of the model label and the screen you are on.

Ask Clyr for help →